KIKAWA KQ 400 N (400w.) CONSTANT PUMP

KIKAWA  KQ 400 N (400w.) CONSTANT PUMP   

General details

KQ Water Pump is an automatic water pump. Everything in the same machine is the pump, the pressure tank and the switch to control the flow of water (Flow switch) flowing water regularly. Noise-degrading and energy saving, designed specifically for household use.

special feature
Water Flow Switch Maintain the pressure level of the pneumatic cylinder pump.
Air pre-charge Dual wiring motor
Automatic anti-heat cut when the water is dry, easy to install.

Manual pump automatic water pressure constant kikawa kq 800

TIP for cover kikawa kq 400

How to remove the lid to check or repair the pump.

- The front of the water pump cover is open.

- Pull the lid window out of the canine slightly slide up.

- Check the water pipe or remove the cover to check the water in the next.

Manual pump automatic water pressure constant kikawa kq 400

TIP for cover KIKAWA kikawa kq 400

How to remove the lid to check or repair the pump.

- The front of the water pump cover is open.

- Pull the lid window out of the canine slightly slide up.

- Check the water pipe or remove the cover to check the water in the next.

General information kikawa kq 400

The kikawa kq 400 automatic water pump is a water pump that combines everything in one machine: the pump, the air pump and the pressure switch (PRESSURE SWITCH).

To With water flow switch and circuit board Designed specifically for household use. The pump keeps the water running continuously in low flow conditions. It also controls the pressure of the water to a constant.

Preparing to install kikawa kq 400 automatic water pump and pipe connection

- In order to keep the pump running continuously, keep the pump stable. Water pump installation area should be dry and well ventilated. There is enough space for maintenance. Or repair in the future. For pumps that need to be installed outside the building. Water pumps should not be outdoors or directly exposed to rain because they will damage the electrical system.

- The water pump should be installed near the water tank or water source as much as possible. All pipe joints should be assembled with caution. To prevent leakage of water. Or bubbles, because it will reduce the efficiency of the pump.

- Do not have foreign substances such as rubber, pvc glue, sand, etc. into the pump. Otherwise the pump may be damaged and the service life will be shortened. It is recommended to use a filter sieve to prevent such foreign matter. Damage to the pump.

- Make sure that the connections are as shown below. (See the panel in the cover) Ensure that grounding or circuit breakers are installed to prevent short circuits.

Circuit diagram of kikawa kq 800 circuit board (Grounding and circuit breaker should be provided to prevent short circuit)

Automatic water pump kikawa kq 400

1. KIKAWA Automatic Water Pump Recommendations

- Do not let the pump dehydrate, do not use hot water at temperatures above 40ºc.

- Do not use with other types of water. In addition to tap water.

2. The electricity is automatically cut off when the temperature is abnormally high. And will return to work when the temperature returns to normal.

3. Before the water pump. The water (water) before.

Removing the control switch of the KQ series

- Turn the flow switch, remove the spring (return spring) and stopper respectively to fill the suction hose and the pump.

- Rotate the ventilation cap.

- Fill the water to full.

4. Check the rotation of the water pump. This is done by using a screwdriver at the end of the motor shaft as shown below. Then rotate the shaft clockwise to check that the pump is rotating freely. If the rotation is not normal. Clean the pump.

5. Check the voltage. Then switch on the water pump. Then open the faucet to use. The water should run out after about 2-3 seconds (in some cases it may take 1-2 minutes).

6. If the water does not flow out of the tap after 1-2 minutes, turn off the water pump immediately. Then go back to step 3 again, fill up the hose and the pump. Then switch the switch.

7. When the water flows out of the faucet to use it. Close and open the faucet to test the water pump. (Water pump will stop automatically when there is no water supply)

8. If you have not used the pump for a long time, please follow the steps above. To test the operation of the water pump. That works normally.

The case can not be resolved from the above steps. Please contact the dealer. Or experienced technicians.

PRESSURE SWITCH kikawa kq 400

The pressure switch is designed to be in the control box. Normally, the pressure is set at the factory to meet the standard operating conditions. If the pump does not work normally. We can adjust the pressure as shown below.

1. The motor case does not stop.

This is because the voltage setting is too high. Flat-blade screwdriver Turn the screw counterclockwise clockwise. Until the motor stops and rotates about 5 degrees more, then check that the motor start is normal.

2. The motor does not start.

This is because the voltage is too low. Fix using a flat-blade screwdriver to turn the screw clockwise. Wait until the motor starts and rotate it a little more by 5 degrees, then check the motor that the motor stops normally.

3. After setting the pressure Replace the screws and replace them.

"Troubleshooting steps"

Read the instructions carefully before making any adjustments. For changing the voltage, the switch cover must be removed. Twist the nut counterclockwise using a 12mm spanner.

Kikawa kq 400 startup procedure for 1st use

For normal water pressure cases, such as the water from a tank that is higher than the water pump.

- should be connected to the water outlet. And the water pipes. For the efficiency of the pumping system.

- water pipe assembly And let the water flow into the pump. (Not switch on the pump)

- It is noted that the water does not flow out of the water.

- Rotate the ventilation cap to expel the air and allow the water to flow.

- When the water flows through the pipe. Close the lid.

- Turn on the water pump.

Kikawa kq 400 first use for the 2nd model

For low water pressure cases such as water in the tank is lower than the water pump.

- Valve feet should be installed * ² at the bottom end of the suction pipe.

- water pipe assembly Then remove the switch (Flow Switch) to fill the water in the channel until the water flows out.

- Close the flow switch carefully.

- Rotate the ventilation cap to expel the air and allow the water to flow.

- Turn on the pump to pump the pump. When the water flows out of the water source, turn off the water pump.

- Close the lid.

- Turn on the pump to operate normally.